How to Install OpenBSD on the Vault

Print
You are here:

OpenBSD Overview

OpenBSD is a common open source UNIX-like operating system. Information regarding OpenBSD can be found on the home page at openbsd.org

Download OpenBSD

OpenBSD is highly configurable and there are multiple versions of OpenBSD and multiple system targets so it is important to get the correct installation file. OpenBSD can be downloaded from one of many mirrors. The mirrors are available at https://www.openbsd.org/ftp.html

Follow these steps to download OpenBSD for the Vault:

  • Select a mirror

  • Select the version of OpenBSD (7.1 was tested for this installation)

  • Select “amd64” for 64 bit

  • For this installation we used a bootable USB select: install71.img
  • Verify that an image is downloaded. For install71.img that will be ~664MB

Burn the installation image to a USB drive

The easiest way to transfer the installation image to a USB drive is by using software called “Rufus” on Windows or “balenaEtcher” on Apple OSX. See this link for detailed instructions on how to create a bootable USB drive using Rufus or balenaEtcher.

Install OpenBSD on The Vault

  • Verify that the Vault is powered down
  • Verify that the VGA or HDMI monitor is connected to the Vault
  • Verify that a USB keyboard is plugged in to the Vault
  • Insert the USB install drive into the another USB port on the Vault
  • While powering up the Vault, press “F11” key and hold it down until it boots to the BIOS and you see the boot options screen
  • Select the USB drive to boot from
  • Verify that the Vault boots and begins the installation process
  • Follow the installation prompts. Note: in most cases the defaults are the desired response.
  • Select (I) for Installation
  • Select the keyboard layout [default]
  • Enter the Hostname (we used “OpenBerkSoftDist” for this example)
  • Select the Network Interface to configure:
    • em0 is “WAN” on the Vault so select [em0]
  • Configure IPv4 address for em0: select [autoconf]
  • Configure IPv6 address for em0: select [none]
  • Which network interface do you wish to configure: select [done]
  • Set the root password: must set 2x to proceed
  • Start ssh(8) by default: recommend [yes]
  • Do you want the X Window System to be started: recommend [yes]
  • Change the default console to com0: recommend [no]
  • Setup a user: recommend [no] for installation
  • Allow root ssh login as desired: recommend [no]
  • Set timezone
  • Which disk is the root disk? Enter ‘?’ to verify the disks: 
    • sd0 should be the mSATA SSD and sd1 the USB
    • If on a VP2410, sd1 will be the onboard Samsung 8GTF4R (7.3GB) and sd2 will be the USB
    • On ALL Vault models: select [sd0] (the SSD)
  • Select (W)hole disk MBR: select [W]
  • Select (A)uto layout: select [A]
  • Which disk do you want to initialize: select [done]
  • Location of sets: enter “disk
  • Is the disk partition already mounted: enter “no
  • Which disk contains the install media:
    • For all FWB Vaults select [sd1]
      • “Which sd1 partition has the install sets?” select [a] (it should be the largest partition)
    • For VP2410 Vault Pros select [sd2]
      • “Which sd2 partition has the install sets?” select [a] (it should be the largest partition)
  • Pathname to the sets: select default [7.1/amd64]
  • Verify all sets are selected (will be an “X” next to each set)
  • Set name(s), select [done]
  • If prompted for SHA256.sig, continue without verification: enter “yes
  • Installation will continue
  • Location of sets: (Second time it asks this) select [done]
  • Installation will continue
  • Select (R)eboot and remove USB when screen goes black
  • Verify system boots to the login prompt
  • Login as “root” with the password set during installation
  • OpenBSD is now successfully installed on The Vault

System Compatibility

The table below shows the latest tested release of OpenBSD on each of the Vaults.

VaultLatest Version TestedBIOS - AMIBIOS - coreboot
FW2BOpenBSD 7.1TestedTested
FW4BOpenBSD 7.1TestedTested
VP2410OpenBSD 7.1TestedN/A
FW6AOpenBSD 7.1TestedTested
FW6BOpenBSD 7.1TestedTested
FW6COpenBSD 7.1TestedTested
FW6DOpenBSD 7.1TestedTested
FW6EOpenBSD 7.1TestedTested

At this point, OpenBSD should be up and running on The Vault.  However, if you experience any issues, please feel free to reach out to us at: support@protectli.com or find more information in our Knowledge Base.

Table of Contents